DIY Ombre Pen Pots

Ombre Pen Pots from Style Me Pretty | The Lovely Drawer

As you can see in addition to writing and reading, this gal LOVES her some pretty. Pretty everything. And if you’re like me, then you still appreciate the use of pen and paper over tablets and smartphones. So if you’re in need of a reading/writing break, here’s a fun DIY project from Style Me Pretty for you to try out this week-end!

What You’ll Need:

  • thick card (not corrugated)
  • toilet roll tube
  • strong glue
  • ruler
  • packing tape and double sided tape
  • scalpel and scissors
  • baking beads or stones
  • jug
  • plaster of paris
  • water
  • spray paint

Make It Happen:

Step 1: Decide how tall you want your pot and how wide you want each panel to be. I made mine 4cm wide and so measured out five panels 4cm x the height side by side, adding a thinner panel flap at the end. Cut the whole thing out with your scalpel and ruler and score down each line. Don’t press too hard.

Step 2: Cover the whole of the inside with packing tape, leaving no gaps apart from the extra flap. This will allow for the plaster shape to come away from the mould easily. I cut 4 cm strips of tape to try and fit within the panels and allow for a smoother finish on the outside.

Step 3: Then to be on the safe side I put a strip of double-sided tape along the thinner flap (taped side) with the strong glue and pulled the shape together to form a polygon. Fix the flap to the outside of the mould. Hold firmly together for a minute until stuck an then I added some packing tape to make sure the join was sealed.

Step 4: Tape the outside of the toilet roll tube in the same way and then draw round the bottom of both the toilet roll tube and your polygon pot and cut out.

Step 5: Then put some glue around the rim of each and attach to the bottom. Hold in place until they adhere. Then seal with packing tape to reinforce and cover any gaps. You can also do this on each fold of the polygon to protect the weak spots. I’d say go to town with tape on both the roll and your pot shape. It doesn’t need to look pretty right now. Attach tape (I used double sided as it’s so strong) to the inside of the toilet roll tube on either side, lower it into the pot and attach the tape strips to the sides. Go over this with packing tape too if you’d like. Fill the toilet roll tube with baking beads to weigh down.

Step 6: Then mix your plaster of paris and water according to the instructions on the packet. I did this in a jug to make pouring easier. Once mixed pour into the mould. You may need to hold the toilet roll tube down if it starts to bob up. Tape the mould on the table a few times to get rid of air bubbles. If any leaks occur just get your tape and try and patch it up but don’t move it around too much. Leave for at least 2 hours to set.

Step 7: Remove the baking beads. Cut the tape strips holding the tube and cut away your outer mould. Then pull out the tube roll. If you struggle as I did with one of mine, then start cutting strips into it and wiggle it out. Then in a well-ventilated area spray on your ombre effect. You can do this by holding the pot on its side and using the spray paint on its side as well. Do small bursts of paint from the bottom and move the can closer to make it go slightly further up the sides.

Step 8: Leave to dry and then you’re done! Time for this little pot to make a new home on your desk.

See the original post with more pictures at Style Me Pretty!

See also, The Lovely Drawer

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

w

Connecting to %s